Видео

Worked on my optima from .5 volts to 11.30 volts jumping with car first then charged over nite on regular charger now 13.1 volts plus it worked on my flooded lead acid lawn tractor battery Thanks Great post

Cómo se quita de el motor ?

O, an old video… It’s even simpler: Connect dead Optima with a charged lead acid battery in parallel and hook up a charger to those two.

Will a grown hog fish win against a grown barracuda

Can I charge the battery just letting the engine run after jumping?

Thanks for the useful information. Regarding your comment about the cost for a few seals, I bought the kit in NZ for over $475. Probably less than $10 for the seals individually from 3rd party. Live and learn.

FUUUUUUCCCCKKKK!!!!!!!

Great video but your trim has been rebuilt by someone else and not done correctly. The cap they used was the wrong one. The mark on it confirms this and I have seen this before. If there is a little pin on the end of the piston shaft head (the end with the ball bearings and springs) then you will need a cap with a machined groove. The pin is a pressure bypass that works when the piston is at full extension to stop you jamming the piston into the cap. it also allows air to be blead out of the piston. You run the piston all the way out and keep going for a count of 5 and this will blead the system. Now with all that said. It is possible to use the flat cap on one of these with a file and 5 minuets of work. First you need to remove the little pressure release pin and then file down flat the hump where the pin came out on the other side. You should now have 4 humps the same height. Now bath the whole thing (in what ever works for you) to get rid of any filings. Then reassemble. Put the bearings and springs back in (not the little pin). Mine also had spring guides but I have seen some with and without. Add oil to the reserve and run the piston out as far as it will go. You will have to do this a few times to bleed the air out but it will work. I did this to mine over a year ago and it has worked perfectly. Just remember to set your trim limiter so you don't jam the piston head in to the cap.

Holy shit!! Never use a metal pice of pipe to extract gas and make sure any pump you use is spark protected. And why doesn’t this fool have a water separation filter set up?

When 5ft Cu pipe was 7$....

good video I have my evinrude etec 90 hp that the trim is lowered only that it is failing

Smart chargers suck getting old school dumb charger it will just blast juice in there until it revives it 😎

Do you put the spark plugs back in after you pour the mystery in and let it sit? Do you add more mystery lubricant every 24 hours? Thank you! This video I’m hoping fixes my proble

Genius! Was stuck on this today but this looks like the solution! Ty subscribing now!

I quit watchin when I saw the adjustable wrench

Your old trim cap is wrong ! Some one has been in that unit before you The cap that came from the factory had the groove in it and you are also missing the pressure relief pin Under one of the springs ... That witness mark or dot on your old cap came from it crashing into the protrusion on the piston assembly

Hi do you no where you got the seal kit please ?

a tip for use with remote gas tanks and push on hose --- eng will idle but not rev up --- check tiny o ring in hose cnn. both ends it will have a small hole in ring lets air in not gas to remove insert fish hook in o ring jerk it out put small amt, lub on new o ring push in easy to fix ----buy these o rings at boat shops keep spare in tackle box it may save alot of paddling some day

harbor freight has a battery operated fuel pump to empty your tank uses d batterys cheap but works great

Does it stop leaking after that ?

A+

Does turning the engine over without water damage the impeller

STILL relevant 6 years later...

I just picked up a free 50 hp force locked up.. trying these steps. I'm guessing it's toasted, but for free I couldn't pass it up.

Dude….. I think your T/T has already been rebuilt already and the wrong cap used. Look at the pics in the instructions and see the difference of what the groove is supposed to look like. Not the same as your used cap.

My local shop will do it for 500 bucks with parts. I'm going there.

Great video, we are attempting this next week. Can you help us in finding the expanding wrench on Amazon. What is it exactly called and what size you used. Thanks

Wife and will there at the end of March, staying at the Saint, loved the info,thanks!!

Thank buddy Jesus it worked … just bought one for 50 buck did to it it was at 4 volts now it works and the guy wants it back … nw

Do you remove Marvel mystery oil after the engine has unseized? If so, how?

He's a brave man working on a glass table.

Great idea! Thanks! I'm going to try this. Installing a holding tank on my boat now. Will let you know how it turns out!

No your the RUclipsr! Thanks good video.

Will be down there the week of June 13th where can we meet up?

Where is the cleaning the fuel tank part? I know how to remove bad gas from the tank.

I also have a DD 6-71, where do you get your DD parts?

Good useful info

Great idea! Thanks for the video. I bought a small Aquasport that was using portable tanks & Im looking to get the tank up & functional.

Do I put the oil in before putting the shaft or put shaft in and fill through screw hole ?

thanks for the video and info this what I have to do to 1 of mine

Yes. I'm here for that

Not really, it will work just give that oil time to work. Don’t get impatient and get the torque bar on it if you haven’t let the oil sit or you will do more damage. Just understand if it seized you probably have a bigger issue somewhere.

My yamaha 150 is doing the same thing going to try this hope it works any last minute pointers ?

Damn 400$ just got one for 273$

Thanks we’re going to be there for xmas. I booked all the places you talked about . Good food ,good weather and Great drinks . Going to be a Blast and excited to try all your suggestions

If your diesel tank doesn't have an inspection hatch you can easy retrofit one from a company in Australia www.cleandiesel.com.au/shop/

I’m here now

thanks for the tip

Honest....where's the bloody beaches

diving is better in key largo...half shell raw bar..louies backyard.... Go north to islamorada for food..key west is a great place to get drunk..